Lost your key fob or need to program a new one for your 2006 Pontiac G6? Heading to a dealership can be expensive and time-consuming. The good news is you can program a new key fob yourself, saving you both money and hassle. This guide provides clear, easy-to-follow instructions to get your 06 G6 Key Fob programmed and working in no time.
What You’ll Need
Before you begin, make sure you have the following:
- Your 2006 Pontiac G6 vehicle.
- Your new, unprogrammed key fob for a Pontiac G6 (ensure it’s compatible).
- Your vehicle’s keys.
Step-by-Step Programming Instructions for Your 06 G6 Key Fob
Follow these steps carefully to program your key fob. It’s recommended to perform these steps from the front passenger seat for easier access to the fuse panel.
- Get Comfortable: Sit in the driver’s seat or, ideally, the front passenger seat of your Pontiac G6.
- Remove the Key: Take the ignition key out of the ignition lock cylinder.
- Close All Doors: Ensure all doors of your vehicle are completely closed.
- Locate and Remove the MALL PGM Fuse: Find the fuse panel in your Pontiac G6. Consult your owner’s manual if you’re unsure of its location. Identify and remove the “MALL PGM” fuse from the fuse panel. Refer to your vehicle’s manual for the exact fuse box location and fuse identification.
- Turn Ignition to ACC: Insert your key into the ignition lock cylinder and turn it to the “ACC” (Accessory) position.
- Cycle Ignition ACC to OFF: Turn the ignition lock cylinder from the “ACC” position to the “OFF” position, and then quickly back to “ACC” within one second.
- Open and Close the Door: Open and then close any vehicle door.
- Listen for the Chime: You should hear an audible chime. This chime indicates that the remote control door lock receiver has entered programming/diagnostic mode. If you don’t hear a chime, repeat steps 1 through 7 again.
- Program the Transmitter:
- Press and Hold: Press and hold both the “LOCK” and “UNLOCK” buttons on your new key fob simultaneously for approximately 14 seconds.
- Synchronization Chime (Optional): After about 7 seconds, you may hear a chime confirming successful synchronization.
- Programming Confirmation Chime: After approximately 14 seconds of holding the buttons, you should hear another chime. This chime confirms that the key fob has been successfully programmed.
- Program Additional Transmitters (If Necessary): If you have additional key fobs to program (up to a maximum of 4), repeat step 9 for each additional fob.
- Remove Key and Reinstall Fuse: Remove the ignition key from the ignition lock cylinder. Locate the “MALL PGM” fuse you removed earlier and reinstall it back into its original position in the fuse panel.
- Test Your Key Fobs: Thoroughly test all programmed key fobs to ensure they are working correctly. Check the lock, unlock, and any other functions your key fob may have.
Important Notes
- Erase Previous Programming: When the keyless entry receiver enters programming mode, it erases all previously programmed key fobs. Therefore, you must program all of your key fobs (both old and new) during this procedure.
- Program One Vehicle at a Time: If you are programming key fobs for multiple vehicles, program them one vehicle at a time. Programming multiple vehicles simultaneously can lead to a key fob being incorrectly programmed to more than one vehicle.
- Timing is Key: The timing in steps 6, 7, and 9 is important for successful programming. If you don’t hear the chimes, double-check your steps and try again.
Troubleshooting
- No Chime: If you don’t hear a chime after step 7, ensure you have correctly performed each step, especially the timing in step 6. Double-check that the MALL PGM fuse was removed and reinstalled correctly.
- Key Fob Not Working: After programming, if the key fob still doesn’t work, ensure you purchased a compatible key fob for your 2006 Pontiac G6. Also, check the battery in your new key fob.
- Still Having Issues? If you continue to experience problems, it’s advisable to consult a professional locksmith or your local Pontiac dealership for assistance.
By following these instructions, you can successfully program your 06 G6 key fob and regain the convenience of keyless entry without the high cost of dealership programming. Enjoy the ease of using your newly programmed key fob!
