Is your 2006 Scion XB key fob malfunctioning, or did you recently get a replacement key fob and need to program it? You’re in the right place. Programming your key fob for your 2006 Scion XB can often be done in a few easy steps right at home, saving you time and money compared to dealership programming. This guide provides a clear, step-by-step process to program your 2006 Scion XB key fob, ensuring you regain remote access to your vehicle quickly.
Before you begin, ensure you have the correct replacement key fob for your 2006 Scion XB. A compatible key fob is crucial for successful programming. This guide is specifically for the HYQ12BBX model, a common key fob type for the 2006 Scion XB. Let’s get started with the programming procedure.
Step-by-Step Programming Instructions for Your 2006 Scion XB Key Fob
Follow these instructions carefully to program your 2006 Scion XB key fob:
-
Start with the Driver’s Door Open: Make sure the driver’s side door is open and the key is completely removed from the ignition switch. This is the initial step to activate the programming sequence.
-
Key Insertion and Removal (Twice): Within 5 seconds, insert your key into the ignition switch and remove it. Repeat this insert and remove action a second time. Timing is important in this step to properly initiate the programming mode.
-
Door Close and Open (Twice): Within 40 seconds after the key actions, close and then open the driver’s side door twice. This action further prepares the vehicle to enter programming mode.
-
Key Insertion and Removal (Once): Immediately insert the key into the ignition switch one more time and remove it. This step is crucial for signaling to the car that you are ready to program the key fob.
-
Door Close and Open (Twice Again): Within 40 seconds, close and open the driver’s door twice again. This sequence of door and key actions is essential for accessing the key fob programming mode in your 2006 Scion XB.
-
Ignition Key and Door Closure: Insert the key into the ignition switch and ensure the driver’s door is now closed. You are now set to use the ignition switch to select the programming mode.
-
Select Programming Mode with Ignition Switch: This step determines whether you are adding a remote, replacing one, checking existing remotes, or erasing all remotes.
- For adding a remote (retaining existing codes): Switch the ignition ON and OFF once.
- For programming a remote (erasing original codes): Switch the ignition ON and OFF twice.
- To check the number of registered remotes: Switch the ignition ON and OFF three times. The system will then blink the door locks to indicate the number of programmed remotes.
- To erase all registered remotes: Switch the ignition ON and OFF five times.
-
Remove Key from Ignition: Take the key out of the ignition switch after performing the ignition ON/OFF sequence.
-
System Response – Lock/Unlock Cycle: The vehicle’s system should respond by locking and unlocking the doors once, twice, or five times, depending on the mode selected in the previous step. It will also lock and unlock slowly one to four times to indicate the number of remotes currently programmed (in check mode).
-
Simultaneous Button Press (Lock and Unlock): Within 40 seconds of the system response, press and release the LOCK and UNLOCK buttons on your new key fob simultaneously.
-
Press Lock or Unlock Button: Within 3 seconds of step 10, press and release either the LOCK or the UNLOCK button on the key fob.
-
Confirmation of Programming: The system should respond by locking and unlocking the vehicle once to confirm successful key fob registration. If it locks and unlocks twice, programming has failed, and you may need to repeat the process.
-
Programming Additional Remotes (Optional): If you have additional key fobs to program, repeat step 10 through step 12 within 40 seconds to program up to 4 remotes.
-
Exit Programming Mode: To exit the programming mode, simply open the driver’s door.
Figure 1: 2006 Scion XB key fob model HYQ12BBX, essential for DIY programming.
By following these steps, you should be able to successfully program your 2006 Scion XB key fob. Ensure you are using a compatible key fob, like the HYQ12BBX model shown, for the process to work smoothly. If you encounter difficulties or prefer professional assistance, remember to search for a qualified key fob installer in your local area for help. You can also find replacement key fobs and further assistance at Keylessentryremotefob.com.
