Lost your key fob or need to program a new one for your 2007 Toyota FJ Cruiser? You might think a trip to the dealership is inevitable, but you could be mistaken. Programming your key fob at home is possible and can save you both time and money. This guide, based on official Toyota technical service bulletin information (TSB#EL009-07), provides a step-by-step process to program your 2007 FJ Cruiser key fob yourself.
Before you begin, ensure you have your new key fob and are ready to follow these instructions precisely. Incorrect steps or timing can lead to unsuccessful programming, so pay close attention to each instruction.
Programming Steps
Make sure the driver’s door is open and unlocked, and the key is out of the ignition before starting.
-
Key Insertion Cycle: Insert and remove the key from the ignition switch twice within 5 seconds. This action initiates the programming sequence in your FJ Cruiser’s system.
Alt text: Inserting a car key into the ignition switch to start the key fob programming process for a 2007 FJ Cruiser.
-
Door Close-Open Cycle (Part 1): Close and open the driver’s door twice. This step is crucial for signaling the system to move to the next stage of programming.
-
Key Insertion Cycle (Part 2): Insert the key into the ignition and remove it once. This further prepares the system for mode selection.
-
Door Close-Open Cycle (Part 2): Close and open the driver’s door twice again. This action continues the communication with the vehicle’s computer to enter programming mode.
-
Key Insertion (Final): Insert the key into the ignition for the last time in this sequence.
-
Door Closure: Close the driver’s door.
-
Mode Selection: This is where you choose the programming mode. Turn the ignition switch from “LOCK” to “ON” and back to “LOCK” at approximately 1-second intervals to select your desired mode. The number of cycles determines the mode:
- 1 time: ADD mode – Use this mode to program an additional key fob without erasing previously programmed fobs.
- 2 times: REWRITE mode – This mode erases all existing key fob programming and allows you to program a new set of fobs. Use this if you want to replace lost or stolen fobs and ensure only the new ones work.
- 3 times: CONFIRMATION mode – This mode allows you to check how many key fobs are currently programmed to your vehicle. The system will respond by cycling the power locks.
- 5 times: PROHIBITION mode – This mode erases all programmed key fobs.
Alt text: Turning the ignition switch of a 2007 FJ Cruiser between LOCK and ON positions to select the key fob programming mode.
-
Key Removal & Mode Confirmation: Remove the key from the ignition. The power locks will cycle “lock” to “unlock” to confirm your mode selection. The number of cycles will match the number of times you cycled the ignition in step 7, confirming the selected mode.
-
Confirmation/Prohibition Mode Completion: If you selected CONFIRMATION or PROHIBITION modes, simply opening the driver’s door will complete the procedure. No further action is needed.
-
ADD or REWRITE Mode – Transmitter Programming: If you are in ADD or REWRITE mode, you have 40 seconds after the door lock confirmation to proceed with programming your key fob transmitter:
-
A – Button Press (Simultaneous): Press and hold both the LOCK and UNLOCK buttons on the key fob simultaneously for 1 to 1.5 seconds, and then release. It might take a few attempts to get the timing right; ensure you are not holding the buttons for too long.
-
B – Button Press (LOCK): Within 3 seconds of step A, press and hold the LOCK button on the key fob for more than 1 second, and then release.
- Successful Programming: If the key fob is successfully programmed, the power locks will cycle “lock” to “unlock” once.
- Unsuccessful Programming: If the locks cycle twice, it indicates a problem. Double-check that you have the correct key fob for your 2007 FJ Cruiser and repeat the entire procedure carefully.
-
C – Multiple Remotes: To program additional key fobs, repeat steps A and B for each fob within the 40-second window.
Alt text: Pressing the lock and unlock buttons on a 2007 FJ Cruiser key fob during the programming sequence.
-
-
Exit Programming Mode: Open the driver’s door to finalize and exit the key fob programming mode.
-
Error Correction: If you make a mistake during the programming process, turn the ignition key to the “ON” position and then back to “LOCK”. This action will erase any entered steps and allow you to start over.
Vehicle Compatibility
While these instructions are specifically for the 2007 Fj Cruiser Key Fob Programming, this procedure is also confirmed to work for these Toyota models:
- 2000 – 2005 Celica
- 2001 – 2003 Prius
- 2001 – 2005 ECHO
- 2001 – 2007 Highlander
- 2001 – 2008 RAV4
- 2002 – 2006 Camry
- 2003 – 2008 Avalon, Corolla, and Matrix
- 2004 – 2008 Sienna and Solara
- 2005 – 2008 Tacoma
- 2007 – 2008 Yaris
Conclusion
Programming your 2007 FJ Cruiser key fob doesn’t have to be a complicated or expensive task. By following these steps carefully, you can easily add or rewrite your key fob programming from the comfort of your own garage. Remember to be precise with the timing and steps for successful programming. If you encounter issues, double-check each step and ensure you have the correct key fob model for your vehicle. Enjoy the convenience of your newly programmed key fob!
