Is your 2008 Scion Xb Key Fob set to only unlock the driver’s door with a single press? While this is the factory default setting for security, many owners prefer the convenience of unlocking all doors at once. The good news is that you can easily reprogram your 2008 Scion xB key fob to unlock all doors with a single press of the unlock button. This guide will walk you through the simple steps to customize your key fob’s behavior, enhancing your daily driving experience.
Understanding Your 2008 Scion xB Key Fob’s Unlock Settings
By default, the Remote Keyless Entry (RKE) system in your 2008 Scion xB is configured for single-stage unlocking. This means a single press of the UNLOCK button on your key fob will only unlock the driver’s door. A second press within 3 seconds is required to unlock the remaining doors. This feature is designed as a security measure, but it can be less convenient if you frequently have passengers or need to access other doors quickly.
Fortunately, Scion designed the system to be user-programmable. You can easily switch to a two-stage unlock mode, where a single press of the UNLOCK button will unlock all doors simultaneously. This modification doesn’t require any special tools or professional assistance and can be done in just a few minutes following these straightforward instructions.
Step-by-Step Guide to Program Your 2008 Scion xB Key Fob for All Doors Unlock
Follow these steps carefully to reprogram your 2008 Scion xB key fob to unlock all doors with one press. It’s important to complete each step within the given timeframe (40 seconds for the entire procedure) for successful programming.
Before You Begin
- Open the Driver’s Door: Ensure the driver’s side door is open throughout the programming process.
- Remove Key from Ignition: Take your 2008 Scion xB key completely out of the ignition switch.
Programming Procedure (Complete within 40 seconds)
- Insert and Remove Key Twice: Insert your key into the ignition switch and immediately remove it. Repeat this action once more (two times total).
- Close and Open Driver’s Door Twice: Close the driver’s door, then open it. Repeat this action once more (two times total).
- Insert and Remove Key Once: Insert your key into the ignition switch and immediately remove it one time.
- Close and Open Driver’s Door Twice: Close the driver’s door, then open it. Repeat this action once more (two times total).
- Insert and Leave Key in Ignition: Insert your key into the ignition switch and leave it in the ignition – do not turn it.
- Close Driver’s Door: Close the driver’s door.
- Turn Key to ON and Back to LOCK Four Times: Turn the ignition key from the LOCK position to the ON position and then back to the LOCK position. Repeat this sequence until you have done it four times, ending in the LOCK position. Do not start the engine.
- Remove Key from Ignition: Take the key out of the ignition switch.
Program Mode Confirmation
If you have correctly completed the steps above, your 2008 Scion xB will enter program mode. You will receive confirmation through the following:
- The tail lights and marker lights will flash 4 times.
- The buzzer will chirp 4 times.
- The door locks will cycle, locking and unlocking 4 times.
This confirmation sequence indicates that your vehicle is now ready to accept the new key fob programming setting.
Select the Operating Mode and Complete Programming
-
Press and Hold LOCK and UNLOCK Buttons: Press and hold both the LOCK and UNLOCK buttons on your 2008 Scion xB key fob simultaneously for about 1 second, then release both buttons at the same time.
-
Choose Your Unlock Mode:
-
To Enable ALL DOORS UNLOCK: Immediately after releasing the LOCK and UNLOCK buttons, press and release the UNLOCK button one time. This will program your key fob to unlock all doors with a single press.
-
To Disable ALL DOORS UNLOCK ( вернуться to Driver’s Door Unlock Only): If you want to revert back to the original setting (driver’s door unlock only), immediately after releasing the LOCK and UNLOCK buttons, press and release the LOCK button one time.
-
-
Confirmation of Mode Selection: After selecting your desired mode, you will receive confirmation:
- The tail lights and marker lights will flash 1 time.
- The buzzer will chirp 1 time.
- The door locks will cycle, locking and unlocking 1 time.
Note: If the system locks and unlocks the doors twice during this step, it indicates an error, and you may need to start the programming procedure over from the beginning.
-
Complete Programming: Open the driver’s door. This action signals the system that programming is complete.
Troubleshooting Tips for 2008 Scion xB Key Fob Programming
- Timing is Crucial: The 40-second time limit for the programming procedure is important. Ensure you complete all steps within this timeframe. If you exceed 40 seconds, the system may time out, and you’ll need to start again.
- Correct Sequence: Double-check that you are performing each step in the exact order described. Even a slight deviation can prevent successful programming.
- Multiple Attempts: As noted by other users, it may take a few attempts to get the programming sequence exactly right. Don’t be discouraged if it doesn’t work on the first try. Carefully review the steps and try again.
- Check Key Fob Battery: While less likely to be the cause, a weak battery in your 2008 Scion xB key fob could potentially interfere with the programming process. Ensure your key fob battery is in good condition.
By following these detailed instructions, you can easily customize your 2008 Scion xB key fob to unlock all doors with a single press, adding convenience to your everyday use of your vehicle.
