How to Program a 2010 Chevy Impala Key Fob: Step-by-Step Guide

Is your 2010 Chevy Impala key fob not working? Perhaps you’ve purchased a new key fob and need to get it programmed to your vehicle. Whatever the reason, programming your key fob yourself can save you time and money compared to a dealership visit. This guide provides clear, easy-to-follow instructions for programming a 2010 Chevrolet Impala key fob, ensuring you regain remote access to your vehicle quickly.

This article outlines two procedures for programming your 2010 Chevy Impala key fob, depending on whether your vehicle is equipped with a Driver Information Center (DIC). Don’t worry if you’re unsure; we’ll walk you through how to determine which procedure applies to your Impala.

Procedure #1: For Vehicles With a Driver Information Center

The Driver Information Center is a digital display within your instrument cluster that provides vehicle information. If your 2010 Chevy Impala has this feature, you’ll find control buttons on your steering wheel, one of which will be marked with an “i” symbol. This procedure utilizes these controls to enter programming mode.

Here’s how to program your key fob if your Impala has a Driver Information Center:

  1. Turn the Ignition to the “On” Position: Insert your key into the ignition. Turn the key to the “On” position, which is just before you start the engine. Do not start the car. The dashboard lights should be illuminated.

  2. Access “Relearn Remote Key” in the DIC: Locate the “Information” button on your steering wheel (marked with “i”). Press this button repeatedly until the Driver Information Center display shows “Relearn Remote Key.”

  3. Activate Remote Key Learning Mode: Once “Relearn Remote Key” is displayed, press the “Set/Reset” button. This button usually has a checkmark symbol. Press and hold it until the DIC display changes to “Remote Key Learning Active.” The vehicle is now in programming mode and ready to learn your key fob signal.

  4. Program the Key Fob: Take the key fob you want to program. Simultaneously press and hold both the “Lock” and “Unlock” buttons on the fob. Continue holding them until the vehicle chimes twice. These chimes indicate that the key fob has been successfully programmed. If you have additional key fobs (new or existing) that you want to use with your 2010 Chevy Impala, repeat this step (step 4) for each of them immediately. It’s crucial to program all desired remotes in this step, as programming a new remote may erase previously programmed ones if not done in the same sequence.

  5. Exit Programming Mode: Turn the ignition key to the “Off” position. This will exit the key fob programming mode. Test all programmed key fobs to ensure they are working correctly by locking and unlocking your doors and, if applicable, using the remote start feature.

Procedure #2: For Vehicles Without a Driver Information Center

If your 2010 Chevy Impala does not have the Driver Information Center and the “Information” button on the steering wheel, you will use the trip odometer reset button to enter the key fob programming mode. This procedure is slightly different but equally straightforward.

Follow these steps to program your key fob on a 2010 Chevy Impala without a DIC:

  1. Turn the Ignition to the “On” Position: Insert your key into the ignition and turn it to the “On” position, just before starting the engine. Do not start the car.

  2. Access “Relearn Remote Key” Using Trip Reset Button: Locate the trip odometer reset button, typically found on the instrument panel near the speedometer. Press and release this button repeatedly until the display shows “Relearn Remote Key.”

  3. Activate Remote Key Learning Mode: Once “Relearn Remote Key” is displayed, press and hold the trip odometer reset button down until the display changes to “Remote Key Learning Active.” The vehicle will now be in the remote programming mode.

  4. Program the Key Fob: Take the key fob you wish to program. Press and hold both the “Lock” and “Unlock” buttons simultaneously on the key fob until the vehicle chimes. The chimes confirm successful programming of that key fob. If you have more key fobs to program, repeat step 4 for each one immediately. Remember to program all your desired remotes at this time.

  5. Exit Programming Mode: Turn the ignition key to the “Off” position to exit the programming sequence. Test each key fob to verify successful programming by testing the lock, unlock, and other remote functions.

Important Note About Programming All Remotes

It’s vital to remember that during the programming process, you must program all of your key fobs – both new and existing – in one programming session. If you only program a new key fob, any previously programmed remotes may no longer work. This is because the system typically clears its memory of old codes when a new programming session begins. Therefore, gather all the key fobs you intend to use with your 2010 Chevy Impala before starting either of the procedures above.

By following these step-by-step instructions, you should be able to successfully program your 2010 Chevy Impala key fob. This DIY approach can save you both time and expense. If you encounter any difficulties or prefer professional assistance, you can always search for a local key fob programming service in your area.

Comments

No comments yet. Why don’t you start the discussion?

Leave a Reply

Your email address will not be published. Required fields are marked *