Losing or needing to replace a key fob for your 2012 Cadillac SRX can be inconvenient, but programming a new one doesn’t have to be a trip to the dealership. Fortunately, Cadillac has equipped the SRX with an owner-programmable system, allowing you to add new key fobs right in your driveway. This guide provides step-by-step instructions for 2012 Cadillac Srx Key Fob Programming, covering scenarios whether you have an existing working remote or if you’re starting from scratch with no programmed fobs.
Programming a New Key Fob When You Have a Working Remote
If you already have one functioning key fob for your 2012 Cadillac SRX and wish to program an additional one, the process is straightforward. Here’s how to program your 2012 Cadillac SRX key fob when you have a working remote:
-
Ensure your Cadillac SRX is turned off completely. The vehicle needs to be in the off position for the programming sequence to begin correctly.
-
Place your existing, working remote key fob in the designated cupholder. This is crucial as the system needs to detect a recognized fob to initiate the adding of a new one.
-
Take your new, unprogrammed remote fob and have it ready. Keep it within reach as you’ll need it shortly for the next steps in the 2012 Cadillac SRX key fob programming procedure.
-
Locate the key lock cylinder on the exterior of your driver’s side door. Insert your vehicle’s key into this lock cylinder.
-
Turn the key to the unlock position rapidly five times within a ten-second timeframe. This action signals the vehicle to enter the key fob programming mode.
-
Observe the Driver Information Center (DIC) display. After correctly performing the previous step, the DIC should display “Ready to Learn Electronic key #2, 3, 4 ETC.” This message confirms that your 2012 Cadillac SRX is now in the programming mode and ready to learn a new key fob.
-
Access the transmitter pocket. This pocket is located inside the center console, between the driver and front passenger seats. Open the center console storage area and lift up the storage tray to reveal the transmitter pocket.
-
Place the new, unprogrammed remote into the transmitter pocket, ensuring the buttons are facing the front of the vehicle. This pocket is designed to establish communication between the new fob and the car’s receiver.
-
Press the ignition button. Once the new remote is successfully learned, the DIC display will update to indicate it is ready to program the next remote. This confirms the successful programming of your 2012 Cadillac SRX key fob.
-
Remove the newly programmed remote from the transmitter pocket and press the unlock button on the remote to verify it is working correctly.
-
If you have more remotes to program, repeat Steps 6 through 10 for each additional key fob.
-
To exit the programming mode once you have programmed all desired remotes, press and hold the ignition button for ten seconds. This will finalize the 2012 Cadillac SRX key fob programming process.
By following these steps, you can easily program a new key fob for your 2012 Cadillac SRX when you already have a working remote.
Programming a New Key Fob When You Have No Working Remotes
If you’ve lost all your key fobs for your 2012 Cadillac SRX, the programming process is a bit more time-consuming but still achievable without special tools. Here’s how to program your 2012 Cadillac SRX key fob when you have no working remotes:
-
Ensure your Cadillac SRX is completely off. The vehicle must be powered down to initiate the no-remote programming sequence.
-
Insert your vehicle’s key into the key lock cylinder located on the outside of the driver’s side door.
-
Turn the key to the unlock position five times within ten seconds, just as in the previous procedure.
-
Observe the Driver Information Center (DIC) display. This time, the DIC will display “REMOTE LEARN PENDING, PLEASE WAIT.” This indicates that the system is entering a more extended learning mode because no working remote was initially detected.
-
Wait for ten minutes. During this period, the DIC will continue to display “REMOTE LEARN PENDING, PLEASE WAIT.” Patience is key here as the system needs this time to prepare for programming without a recognized fob.
-
After ten minutes, the DIC display will change to “PRESS ENGINE START BUTTON TO LEARN.” At this point, press the ignition button. The DIC will revert to showing “REMOTE LEARN PENDING, PLEASE WAIT” again.
-
Repeat Step 6 two additional times. This means you will go through the ten-minute wait and ignition press sequence a total of three times. This step is crucial for clearing the system of any previously known remotes and preparing it to learn new ones. After the third time, all previously programmed remotes will no longer function with the vehicle.
-
Following the completion of the three cycles, the DIC display should now show “READY FOR REMOTE #1.” This confirms that the 2012 Cadillac SRX is now ready to learn the first new key fob.
-
Place the new, unprogrammed remote into the transmitter pocket, ensuring the buttons face the front of the vehicle. The transmitter pocket remains in the same location within the center console.
-
Press the ignition button. Once the remote is learned, the DIC display will indicate it is ready to program the next remote, confirming successful programming of your first 2012 Cadillac SRX key fob.
-
Remove the newly programmed remote from the transmitter pocket and press the unlock button on the remote to test its functionality.
-
To program additional remotes, repeat Steps 9 through 11 for each new key fob.
-
Once you have programmed all necessary remotes, press and hold the ignition button for ten seconds to exit the programming mode. This finalizes the 2012 Cadillac SRX key fob programming procedure when starting without any working remotes.
This more extended process allows you to regain access and control of your 2012 Cadillac SRX even when all your original key fobs are lost or unavailable.
Successfully programming your 2012 Cadillac SRX key fob yourself can save you time and money. Whether you had a working remote or were starting from zero, these steps should guide you through the process effectively.
