Key fobs provide convenient access and security for your 2010 Cadillac SRX. Programming a new or replacement key fob can seem daunting, but it’s often a straightforward process you can accomplish at home. This guide provides comprehensive instructions for 2010 Cadillac Srx Key Fob Programming, covering scenarios whether you have an existing working remote or if you’ve lost all of them.
Programming a 2010 Cadillac SRX Key Fob When You Have a Working Remote
This method is applicable when you possess at least one functioning key fob and wish to add or program an additional one. Here’s how to program your 2010 Cadillac SRX key fob in this situation:
-
Start with the Vehicle Off: Ensure your 2010 Cadillac SRX is completely turned off. The engine should not be running, and the vehicle should be in park.
-
Prepare Existing and New Remotes: Place your currently working key fob(s) in the vehicle’s cupholder for easy access. Have the new, unprogrammed key fob readily available with you.
-
Use the Driver’s Side Door Lock Cylinder: Locate the key lock cylinder on the exterior of your driver’s side door.
-
Turn the Key to Unlock Repeatedly: Insert your key into the door lock cylinder. Turn the key to the “unlock” position and repeat this action five times in rapid succession, specifically within a ten-second timeframe. This action signals the vehicle to enter programming mode.
-
Observe the Driver Information Center (DIC): After correctly performing the previous step, the Driver Information Center (DIC) display, usually located within your instrument cluster, will illuminate and display a message. This message will read “Ready to Learn Electronic key #2, 3, 4 ETC.”, indicating the system is ready to program additional key fobs.
-
Locate the Transmitter Pocket: Identify the transmitter pocket within your 2010 Cadillac SRX. This pocket is situated inside the center console, positioned between the driver and front passenger seats. To access it, you will likely need to open the center console storage area and lift up the storage tray to reveal the transmitter pocket.
-
Place the New Remote in the Transmitter Pocket: Take the new key fob you intend to program and place it inside the transmitter pocket. Ensure the buttons on the key fob are facing the front of the vehicle as you position it in the pocket.
-
Press the Ignition Button: With the new remote placed in the transmitter pocket, press the ignition button in your Cadillac SRX. Upon successful learning of the new remote, the DIC display will update to indicate it is ready to program the next remote, should you have more to program.
-
Remove and Test the Remote: Take the newly programmed remote out of the transmitter pocket. Press the “unlock” button on the remote to test if it has been successfully programmed. The doors should unlock, confirming successful programming.
-
Program Additional Remotes (If Necessary): If you have more key fobs to program, repeat Steps 6 through 8 for each additional remote.
-
Exit Programming Mode: Once you have programmed all desired key fobs, exit the programming mode by pressing and holding the ignition button for approximately ten seconds. This action will finalize the programming process.
Programming a 2010 Cadillac SRX Key Fob When You Have No Working Remotes
If you have lost all your key fobs for your 2010 Cadillac SRX, or if none are functioning, you will need to follow a slightly different, more time-intensive procedure. This method is designed for situations where no existing programmed remotes are available.
-
Ensure Vehicle is Off: Begin by making sure your 2010 Cadillac SRX is turned off completely.
-
Access the Driver’s Door Lock Cylinder: As before, locate the key lock cylinder on the outside of the driver’s side door.
-
Turn Key to Unlock Position Five Times: Insert your key into the driver’s side door lock cylinder. Turn the key to the “unlock” position five times within ten seconds.
-
Observe DIC Message – “REMOTE LEARN PENDING, PLEASE WAIT”: After turning the key, the Driver Information Center (DIC) will display the message “REMOTE LEARN PENDING, PLEASE WAIT.” This indicates that the system is entering a learn mode but requires a waiting period for security reasons.
-
Wait Ten Minutes and Press Ignition – Repeat Three Times: Wait for a full ten minutes. After ten minutes, the DIC display will change to “PRESS ENGINE START BUTTON TO LEARN.” At this point, press the ignition button. The DIC will revert back to displaying “REMOTE LEARN PENDING, PLEASE WAIT.” You must repeat this Step 5 two additional times. This means you will go through three ten-minute waiting periods in total.
-
“READY FOR REMOTE #1” Display: After the third ten-minute cycle and pressing the ignition button for the third time, the DIC display should finally show “READY FOR REMOTE #1.” Crucially, after this step, any previously programmed remotes will no longer function with your vehicle. This is a security measure to ensure only the remotes you are currently programming will work.
-
Place New Remote in Transmitter Pocket: Locate the transmitter pocket in the center console (as described in the previous method). Place the new key fob you wish to program into the transmitter pocket, with the buttons facing the front of the vehicle.
-
Press the Ignition Button: Press the ignition button. When the remote is successfully learned, the DIC display will indicate that it is ready to program the next remote, if applicable.
-
Remove and Test Remote: Take the programmed remote from the transmitter pocket. Press the “unlock” button to test if programming was successful.
-
Program Additional Remotes (If Desired): To program any additional key fobs, repeat Steps 7 through 9.
-
Exit Programming Mode: Once all key fobs are programmed, press and hold the ignition button for ten seconds to exit the key fob programming mode.
By following these detailed steps, you can successfully program a 2010 Cadillac SRX key fob, whether you have a working remote or are starting from scratch. This do-it-yourself approach can save you time and money, getting you back on the road with a functional key fob.
