Lost your key fob or need to program a new one for your 2007 Pontiac G6? Don’t want to pay dealership prices for a simple procedure? You’re in luck! Programming your 07 Pontiac G6 Key Fob can be done easily at home with a few simple steps, saving you time and money. This guide will walk you through the process, ensuring you can get back on the road quickly with a functioning key fob.
Step-by-Step Guide to Program Your 07 Pontiac G6 Key Fob
Before you begin, ensure you have all the necessary key fobs you intend to program. This procedure will erase all previously programmed key fobs, so you’ll need to reprogram them all at once. You can program up to four key fobs for your Pontiac G6.
Follow these steps carefully:
-
Get Comfortable in the Driver’s Seat: Sit in the driver’s seat of your Pontiac G6. Some find it easier to perform these steps from the front passenger seat, so choose whichever is more comfortable for you.
-
Remove the Ignition Key: Take the ignition key completely out of the ignition lock cylinder.
-
Close All Doors: Make sure all doors of your Pontiac G6, including the trunk or hatch, are fully closed.
-
Locate and Remove the MALL PGM Fuse: You’ll need to access your vehicle’s fuse panel. Refer to your Pontiac G6 owner’s manual to find the exact location of the fuse panel and the “MALL PGM” fuse. Once located, carefully remove this fuse.
-
Turn Ignition to ACC Position: Insert your key into the ignition and turn it to the “ACC” (Accessory) position. This is usually one click before the “ON” or “Run” position.
-
Cycle Ignition ACC to OFF and Back: Turn the ignition from the “ACC” position to the “OFF” position, and then quickly back to “ACC” again, all within one second.
-
Open and Close Any Vehicle Door: Open and then close any door on your Pontiac G6. It doesn’t matter which door you choose.
-
Listen for the Chime: After closing the door, listen carefully for a chime. This chime indicates that the remote control door lock receiver has entered the programming/diagnostic mode. If you do not hear a chime, you need to go back to step 1 and repeat the process.
-
Program the Transmitter(s):
-
Press and Hold Lock and Unlock: For the first key fob you want to program, press and hold both the “LOCK” and “UNLOCK” buttons simultaneously for approximately 14 seconds.
-
Listen for Confirmation Chimes: After about 7 seconds, you might hear a chime confirming synchronization. Continue holding the buttons until approximately 14 seconds have passed. At this point, you should hear another chime confirming successful programming of that key fob.
-
Repeat for Additional Transmitters: If you have more key fobs to program, repeat step 9a and 9b for each additional key fob.
-
-
Remove Ignition Key: Once you have programmed all desired key fobs, remove the ignition key from the ignition lock cylinder.
-
Reinstall the MALL PGM Fuse: Go back to the fuse panel and reinstall the “MALL PGM” fuse in its original location.
-
Test Your Key Fobs: Thoroughly test all the key fobs you just programmed to ensure they are working correctly. Try locking, unlocking, and using any other functions your key fob may have, like remote start or panic button.
Image: Buttons on a standard Pontiac G6 key fob, highlighting lock and unlock for programming instructions.
Important Notes and Tips
- Timing is Key: The timing in steps 6, 7, and 9 is crucial. Make sure to perform the actions within the specified timeframes for successful programming.
- Fuse Location: Always refer to your Pontiac G6 owner’s manual for the precise location of the fuse panel and the “MALL PGM” fuse. Fuse box locations can vary slightly depending on the model year and trim.
- Erase Previous Programming: Remember that starting this programming sequence will erase all previously programmed key fobs. You must reprogram all of them during this session.
- Troubleshooting: If you encounter issues and the key fobs are not programming, double-check each step and ensure you are following the instructions precisely. If problems persist, you may need to consult a qualified mechanic or locksmith.
- Battery Condition: Ensure the batteries in your key fobs are in good condition. Weak batteries can sometimes cause programming issues.
By following these detailed steps, you can successfully program your 07 Pontiac G6 key fob yourself. This DIY approach not only saves you money but also empowers you with the knowledge to handle basic car maintenance tasks. Enjoy the convenience of your newly programmed key fobs!
