Key Fob Battery for Ford Explorer Limited 2013: A Comprehensive Guide

If your key fob for your 2013 Ford Explorer Limited is acting up, the culprit might be a simple, dying battery. This guide will walk you through everything you need to know about replacing the key fob battery for your Ford Explorer Limited 2013, from identifying the right battery to the step-by-step replacement process.

Identifying the Right Key Fob Battery for Your 2013 Ford Explorer Limited

Before you start, it’s crucial to know the correct battery type for your key fob. The 2013 Ford Explorer Limited typically uses a CR2032 3-volt lithium coin battery. This battery is readily available at most electronics stores, pharmacies, and online retailers. Double-checking your owner’s manual is always a good idea to ensure you purchase the correct battery. Using the wrong battery can lead to malfunctions or even damage to your key fob.

Step-by-Step Guide to Replacing Your Key Fob Battery

Replacing the key fob battery for a 2013 Ford Explorer Limited is a straightforward process that you can do at home with minimal tools. Here’s a detailed guide to help you:

Locate the key slot: On the side of your key fob, you’ll find a small slot. This is where you’ll insert your key or a small flathead screwdriver.
Separate the key fob halves: Gently insert your key or screwdriver into the slot and pry the two halves of the key fob apart. Be careful not to use excessive force, as this could damage the plastic casing.
Locate the battery: Once the key fob is open, you should see the CR2032 battery. It’s usually housed in a small compartment or secured by a clip.
Remove the old battery: Carefully remove the old battery. You can use your fingernail or a small flathead screwdriver to pry it out. Be mindful of the battery’s orientation.
Insert the new battery: Place the new CR2032 battery into the compartment, ensuring it matches the orientation of the old battery. You should hear a small click when it’s properly seated.
Reassemble the key fob: Align the two halves of the key fob and press them together until they snap shut.
Test the key fob: Try locking and unlocking your car with the newly installed battery. If it works, you’ve successfully replaced your key fob battery!

Common Key Fob Problems and Solutions

Beyond a dead battery, there are other reasons why your key fob might be malfunctioning. These can range from a weak signal to programming issues. Here are some common problems and their solutions:

Key fob not working at all: Try replacing the battery. If that doesn’t work, the key fob might need to be reprogrammed.
Intermittent key fob operation: This could be due to a weak battery, interference from other electronic devices, or a faulty key fob.
Key fob buttons sticking: Try cleaning the buttons with a soft cloth and some isopropyl alcohol.

How Long Does a Key Fob Battery Last?

The lifespan of a key fob battery can vary, but typically lasts between 2 to 4 years. Factors like frequency of use and environmental conditions can affect battery life.

Key Fob Programming for your Ford Explorer Limited 2013

Sometimes, you may need to reprogram your key fob. This might be necessary after replacing the battery or if the key fob stops working altogether. While some newer vehicles allow for self-programming, you might need professional assistance for a 2013 Ford Explorer Limited. An automotive locksmith or your Ford dealership can handle this.

Conclusion

Replacing the key fob battery for your Ford Explorer Limited 2013 is a simple and cost-effective DIY task. By following the steps outlined in this guide, you can save yourself time and money. However, if you’re experiencing more complex issues, consulting a professional is always recommended. Remember to keep your Key Fob Battery For Ford Explorer Limited 2013 fresh to avoid any unexpected lockouts!

FAQ

What type of battery does a 2013 Ford Explorer Limited key fob use? A CR2032 3-volt lithium coin battery.
How do I know if my key fob battery is dead? Common signs include the key fob not working at all or working intermittently.
Can I reprogram my Ford Explorer Limited 2013 key fob myself? You might need professional assistance.
Where can I purchase a replacement battery? Most electronics stores, pharmacies, and online retailers carry CR2032 batteries.
How long does a key fob battery typically last? Between 2 to 4 years.
What should I do if my key fob still doesn’t work after replacing the battery? Consider professional reprogramming.
What are some common key fob problems besides a dead battery? Intermittent operation, sticking buttons, and complete malfunction.

Common Scenarios

Scenario 1: Key fob completely unresponsive. Solution: Replace the battery. If the problem persists, consult a professional for reprogramming.
Scenario 2: Key fob works intermittently. Solution: Replace the battery. If the problem persists, check for interference or consider a faulty key fob.
Scenario 3: Key fob buttons are sticky. Solution: Clean the buttons with isopropyl alcohol and a soft cloth.