Programming your 2008 Chrysler Sebring Key Fob can be a straightforward process, especially if you already have a working remote. This guide provides two programming procedures to help you get your new or replacement key fob functioning correctly. Before you begin, ensure you have all the remote transmitters you intend to program for your vehicle. If you do not currently have a working key fob, you will need to seek assistance from a qualified locksmith or dealership for programming services.
This guide assumes you have at least one functioning remote transmitter for your 2008 Chrysler Sebring. Please review both procedures carefully before attempting to program your key fob. We recommend trying Procedure 1 first, and if it does not work, proceed to Procedure 2.
Programming Procedure #1
This procedure is generally the simpler of the two and is often successful for 2008 Chrysler Sebring key fobs.
- Prepare Your Vehicle: Enter your 2008 Chrysler Sebring and ensure all doors are closed. Fasten the driver’s seatbelt. Verify that no other individuals are inside the vehicle.
- Ignition Position: Insert the key into the ignition switch. Turn the ignition key to the ON position. This is the position just before you would crank the engine to start the car. The dashboard lights should be illuminated.
- Initiate Programming Mode: Take a currently working remote. Press and hold the UNLOCK button on this remote for a duration of 4 to 10 seconds. While continuously holding the UNLOCK button, press the PANIC button for one second, and then release both buttons simultaneously. Listen carefully for a chime. A chime sound within three seconds indicates that your 2008 Chrysler Sebring has successfully entered the key fob programming mode.
- Program the First Remote: Immediately after hearing the chime and within 30 seconds, press the UNLOCK button on the same remote you used in step 3. You should hear an audible tone. This tone confirms that the vehicle has recognized and re-programmed this remote.
- Program Additional Remotes: If you have more key fobs to program, including any previously working remotes, you must program them at this stage. Within 30 seconds of completing step 4 (or step 3 if you are only programming one new remote), press the UNLOCK button on the next remote you wish to program. You should hear another audible tone, indicating successful programming of that remote. Repeat this step for every additional remote you need to program.
- Exit Programming Mode: Once you have programmed all desired key fobs, turn the ignition switch to the OFF position and remove the key from the ignition.
- Test Your Remotes: Test each programmed remote to ensure it is functioning correctly. Press the lock, unlock, and panic buttons to verify proper operation.
Programming Procedure #2
If Procedure #1 does not successfully program your 2008 Chrysler Sebring key fob, please attempt Procedure #2. The initial steps are similar, but this procedure utilizes both the LOCK and UNLOCK buttons during the programming sequence.
- Vehicle Preparation: Sit inside your 2008 Chrysler Sebring with all doors completely closed and the driver’s seatbelt securely fastened. Ensure the vehicle is empty except for the programmer.
- Ignition to ON: Insert the ignition key and turn it to the ON position. This is the position where the vehicle’s electrical systems are active, but the engine is not started.
- Enter Programming Sequence: Press and hold the UNLOCK button on a functioning remote for 4 to 10 seconds. While holding the UNLOCK button, press and release the PANIC button for one second. Release both buttons at the same time. A chime should sound within 3 seconds, confirming entry into programming mode.
- Remote Recognition and Programming: On the same remote used in step 3, press and hold both the LOCK and UNLOCK buttons simultaneously, then release them. You should hear a tone indicating the remote has been recognized. Immediately after hearing this tone, press and release the UNLOCK button on that same remote. A chime should then sound, confirming that the remote has been programmed. Ensure this entire step is completed within 30 seconds of hearing the initial chime in step 3.
- Programming Additional Remotes: If you have more remotes to program, proceed within 30 seconds of step 4. For each subsequent remote, press and hold the LOCK and UNLOCK buttons simultaneously, then release. Listen for the tone indicating recognition. Once heard, press and release the UNLOCK button on that remote. A chime will confirm programming. Repeat this for all additional remotes, including any previously working ones you wish to ensure are still programmed.
- Complete Programming: Turn the ignition off and remove the key from the ignition.
- Verify Remote Functionality: Thoroughly test all programmed remotes to confirm they are working as expected. Check the lock, unlock, and panic functions on each remote.
Important Considerations:
- Working Remote Requirement: Both of these procedures rely on having at least one pre-programmed, working remote for your 2008 Chrysler Sebring. If you do not have a working remote, these procedures will not work. You will need to visit a qualified locksmith or an authorized Chrysler dealership to have a new key fob programmed.
- Timing is Key: Pay close attention to the timing mentioned in each step, especially the 30-second windows for completing certain actions. If you exceed these time limits, the programming sequence may time out, and you may need to start over.
- Battery Condition: Ensure the batteries in all your key fobs, both working and new, are in good condition. Weak batteries can sometimes cause programming issues.
- Troubleshooting: If you encounter difficulties, re-read the instructions carefully and ensure each step is followed precisely. If you continue to have problems, it is recommended to consult with a professional.
By following these steps, you should be able to successfully program your 2008 Chrysler Sebring key fob. Enjoy the convenience of your newly programmed remote!
