Lost or need to replace your 09 Pontiac G6 Key Fob? Facing a hefty bill from dealerships or locksmiths can be frustrating. The good news is, programming a new key fob for your 2009 Pontiac G6 can often be done yourself, saving you both time and money. This guide provides a straightforward, step-by-step process to program your 09 Pontiac G6 key fob right at home.
Before you begin, it’s important to understand that this procedure is for programming the key fob’s remote functions (locking, unlocking, panic button). If you need to program a new transponder key for starting the engine, that process might be different and could require professional assistance. However, for key fob functionality, follow these instructions carefully.
Here’s how to program your 09 Pontiac G6 key fob without any special tools:
-
Get Comfortable: Sit in the driver’s seat of your Pontiac G6. While the original instructions mention the driver’s seat, some find it slightly easier to perform these steps from the front passenger seat. Choose whichever is more comfortable for you.
-
Remove the Key: Take the ignition key completely out of the ignition lock cylinder.
-
Close All Doors: Ensure all doors of your Pontiac G6, including the trunk or hatchback, are fully closed.
-
Locate and Remove the MALL PGM Fuse: You’ll need to find the fuse panel in your Pontiac G6. Consult your owner’s manual for the precise location of the fuse panel and the MALL PGM fuse. Remove this fuse. This fuse is crucial for initiating the programming sequence.
-
Turn Ignition to ACC: Insert the ignition key into the ignition lock cylinder and turn it to the ACC (Accessory) position. This is usually one click forward from the OFF position.
-
Cycle Ignition ACC and OFF: Quickly turn the ignition lock cylinder from the OFF position to the ACC position, and then back to OFF within one second. This rapid cycling is a key step in entering programming mode.
-
Open and Close the Door: Open and then close any door on your Pontiac G6. This action signals the system to enter programming mode.
-
Listen for the Chime: Pay close attention. You should hear an audible chime sound. This chime indicates that the remote control door lock receiver has successfully entered the programming/diagnostic mode. If you don’t hear a chime, carefully repeat steps 1 through 7. It may take a couple of tries to get the timing right.
-
Prepare to Program: Once you hear the chime, the system is ready to learn new key fob signals.
-
Press and Hold LOCK and UNLOCK: Take the key fob you want to program. Simultaneously press and hold down both the LOCK and UNLOCK buttons on the fob for approximately 14 seconds. Hold them down firmly throughout this period.
-
Listen for Confirmation Chimes: After holding the buttons, listen carefully. You may first hear a chime around 7 seconds, which indicates successful synchronization. Crucially, after approximately 14 seconds of holding the buttons, you should hear another chime. This second chime confirms that the key fob has been successfully programmed to your 09 Pontiac G6.
-
Program Additional Fobs (If Needed): If you have additional 09 Pontiac G6 key fobs to program, repeat step 10 for each additional fob immediately after the confirmation chime in step 11. Remember, you can program up to 4 key fobs for your vehicle. It’s important to program all desired fobs in one programming session because initiating the programming sequence erases all previously programmed fobs.
-
Remove Key and Reinstall Fuse: Take the ignition key out of the ignition lock cylinder. Go back to the fuse panel and reinstall the MALL PGM fuse that you removed in step 4.
-
Test Your Fobs: Thoroughly test all the key fobs you programmed to ensure they are working correctly. Press the LOCK, UNLOCK, and PANIC buttons on each fob to verify they control the door locks and panic alarm as expected.
Important Notes:
- Erase Previous Programming: Be aware that when you enter programming mode, all previously programmed key fobs are erased from the system’s memory. Therefore, you must reprogram all key fobs you want to use with your 09 Pontiac G6 in a single programming session.
- Program One Vehicle at a Time: If you are programming key fobs for multiple vehicles, make sure to program them one vehicle at a time. Programming multiple vehicles simultaneously could lead to a key fob being incorrectly programmed to more than one vehicle’s receiver.
- Check Fuse Location: Always refer to your 2009 Pontiac G6 owner’s manual for the exact location of the fuse panel and the MALL PGM fuse. Fuse box locations can vary slightly depending on the vehicle’s trim and options.
- Aftermarket Key Fobs: These instructions are generally applicable to both OEM (Original Equipment Manufacturer) and aftermarket key fobs designed for the 09 Pontiac G6. However, ensure that any aftermarket key fob you purchase is specifically stated to be compatible with your vehicle’s make, model, and year.
- Professional Help: If you encounter difficulties or are unsure about any step in this process, it’s always best to consult a qualified locksmith or your local Pontiac dealership for assistance. They have the expertise and tools to diagnose and resolve any key fob programming issues.
By following these steps, you should be able to successfully program your 09 Pontiac G6 key fob and regain the convenience of remote locking and unlocking, all while avoiding unnecessary expenses. Check out keyfobprog.com for more DIY car key and key fob programming guides!
