Are you experiencing issues with your 2000 Honda CRV key fob? Perhaps it’s no longer unlocking your doors reliably, or maybe it’s stopped working altogether. The good news is that you can likely resolve this by reprogramming your key fob yourself. Programming a 2000 Honda CRV key fob is a relatively simple procedure that can save you both time and money compared to visiting a dealership. This comprehensive guide will walk you through each step of the process to get your key fob working like new again.
Step-by-Step Programming Guide for Your 2000 Honda CRV Key Fob
Before you begin, it’s important to note that initiating the programming sequence will erase all previously programmed key fobs. Therefore, you will need to reprogram all of your remotes during this process, not just the one you are having trouble with. Ensure you have all key fobs you intend to use readily available before starting. Also, each step must be completed within 5 seconds of the previous one to prevent the system from exiting programming mode prematurely.
Step 1: Turn Ignition Switch to ON (II)
Begin by inserting your key into the ignition of your 2000 Honda CRV. Turn the ignition switch to the “ON” position (II). This is the position right before you would start the engine. The dashboard lights should illuminate, indicating the ignition is in the correct position.
Step 2: Press the LOCK or UNLOCK Button
Take one of your 2000 Honda CRV key fobs – it can be any of them, even one that isn’t currently programmed. Press either the “LOCK” or “UNLOCK” button on this key fob.
Step 3: Turn Ignition Switch to LOCK (0)
Next, turn the ignition switch back to the “LOCK” position (0), effectively turning the ignition off. Do not remove the key from the ignition; simply turn it back to the initial position.
Step 4: Repeat Steps 1, 2, and 3 Two More Times
Now, repeat the sequence of steps 1, 2, and 3 two more times, using the same key fob and buttons as in step 2. This means you will be cycling the ignition ON, pressing a button, and turning it back to LOCK, for a total of three times in a row, always using the same key fob button press.
Step 5: Turn the Ignition Switch to ON (II) Again
After the third cycle, turn the ignition switch to the “ON” position (II) one last time. Leave it in the “ON” position.
Step 6: Press the LOCK or UNLOCK Button (Confirmation)
Press the “LOCK” or “UNLOCK” button on the same key fob you have been using throughout these steps. If you have successfully entered programming mode, the power door locks on your 2000 Honda CRV should cycle (lock and then unlock). This confirms that the system is ready to learn new key fob codes.
Step 7: Program Each Remote
Now, take each key fob you want to program, one at a time. For each key fob, press either the “LOCK” or “UNLOCK” button. After pressing a button on each remote, you should hear the door locks cycle again, indicating that the system has accepted the signal from that particular remote. Repeat this for every key fob you need to program.
Step 8: Turn the Ignition Switch to LOCK (0) to Exit
Once you have programmed all of your 2000 Honda CRV key fobs, turn the ignition switch back to the “LOCK” position (0). This action will exit the key fob programming mode.
Step 9: Test Your Remotes
Finally, test each of your programmed key fobs to ensure they are working correctly. Press the “LOCK” and “UNLOCK” buttons on each remote to verify that they properly control the door locks of your 2000 Honda CRV.
In conclusion, programming your 2000 Honda CRV key fob is a straightforward DIY process that can save you from unnecessary dealership costs. By carefully following these nine steps, you can easily restore the convenience of your keyless entry system. Should you find that your key fob is still unresponsive after programming, or if you require a replacement, visit Keylessentryremotefob.com for a wide selection of 2000 Honda CRV key fobs and other automotive remotes.
