Lost your key fob or need to program a new one for your 2004 Pontiac Grand Am? You might be able to do it yourself right at home! Programming your key fob can seem daunting, but for many 2004 Pontiac Grand Am models, it’s a straightforward process you can tackle without a trip to the dealership. This guide will walk you through the steps to program your 2004 Pontiac Grand Am key fob, saving you time and money.
Step-by-Step Programming Instructions for Your 2004 Pontiac Grand Am Key Fob
Before you begin, it’s important to note that all existing transmitters will need to be reprogrammed during this procedure. Make sure you have all key fobs you intend to use with your vehicle present before starting.
Here’s how to program your 2004 Pontiac Grand Am key fob using the in-vehicle programming method:
- Ensure all vehicle doors are closed. This is crucial for the programming sequence to initiate correctly.
- Insert your key into the ignition. Get ready to turn the ignition as instructed in the following steps.
- Press and HOLD the UNLOCK button located on the driver’s side door panel. Keep holding this button down throughout the next several steps until instructed to release it.
- Perform steps 5 through 8 in rapid succession. Timing is important for this procedure to work. Be ready to quickly turn the ignition as described.
- Turn the ignition switch to the ON position. Do not attempt to start the engine; simply turn the key to the “ON” position where the dashboard lights illuminate.
- Turn the ignition switch to the OFF position. Turn the key back to the “OFF” position.
- Turn the ignition switch back to the ON position again. Again, do not start the engine, just turn it to the “ON” position.
- Turn the ignition switch back to the OFF position. Turn the key back to the “OFF” position one last time.
- Release the UNLOCK button on the door panel. As soon as you release the button, the vehicle should automatically lock and unlock the doors. This confirms that the system has entered programming mode.
- Program your first key fob: Press and HOLD both the LOCK and UNLOCK buttons on the key fob you wish to program simultaneously. Continue holding both buttons until the vehicle doors lock and unlock again. This may take up to 30 seconds. This lock and unlock sequence confirms that the key fob has been successfully programmed.
- Repeat step 10 for any additional key fobs. If you have more key fobs to program (including any previously working fobs), repeat step 10 for each of them.
- Exit programming mode: Turn the ignition switch to the ON position one last time. This will exit the transmitter programming mode.
You should now test each of your programmed key fobs to ensure they are working correctly with your 2004 Pontiac Grand Am.
Important Note: Vehicles Incompatible with This Method
While this procedure works for many vehicles, it’s important to know that these instructions will NOT work for all models, even within the same year. If your 2004 Pontiac Grand Am is one of the specific models listed below, you will need to have your key fob programmed by a qualified locksmith or dealership.
This programming method is not compatible with the following vehicles:
- 2000 – 2004 Cadillac Seville/Deville
- 2001 – 2006 Chevrolet Astro/Express
- 2001 – 2005 Chevrolet Blazer (SUV – not pickup)
- 2001 – 2004 Chevrolet Corvette
- 2001 – 2005 Chevrolet Monte Carlo
- 2001 – 2004 Chevrolet Malibu
- 2001 – 2004 GMC Jimmy
- 2001 – 2005 GMC Safari
- 2000 – 2005 Pontiac Bonneville
- 2004 Pontiac Grand Prix
If your 2004 Pontiac Grand Am is not on this list, the programming steps above are likely to work. However, if you encounter issues or your vehicle is listed above, seeking professional programming services is necessary.
Alternative Programming Method for Certain Chevrolet and Pontiac Models
Some Chevrolet and Pontiac models, including certain Impala and Monte Carlo models from the early 2000s, utilize a different programming method through the car radio. While not explicitly listed for the 2004 Pontiac Grand Am in the original source, it’s worth being aware of this alternative method in case the standard procedure doesn’t work and your vehicle’s radio system offers a “FOB PROG” option in the settings.
For 2001-2005 Chevrolet Impala, Monte Carlo (and potentially other similar models):
- Turn the ignition to ACC or ON, and ensure the radio is OFF. Do not start the engine.
- Press and hold the DISP button on the radio for at least five seconds until “settings” is displayed on the radio screen.
- Use the SEEK up or down arrows to navigate through the settings menu until “FOB PROG” appears on the display.
- Press the PREV or NEXT button to enter the submenu. “BEGIN” will be displayed, and the current selection might have an asterisk next to it.
- Press the DISP button to start the programming process. When “PUSH FOB” flashes on the screen, press and hold the LOCK and UNLOCK buttons on your first key fob simultaneously for 15 seconds. You should hear a chime to confirm the key fob has been learned.
- Repeat Step 5 for each additional key fob you need to program (up to a total of four). You do not need to press the DISP button again; just press and hold the LOCK and UNLOCK buttons on the next key fob.
- To exit programming mode, scroll in the radio settings until “EXIT” appears, and then press the DISP button. You should hear a chime to confirm exit.
Disclaimer: Always refer to your vehicle’s owner’s manual for the most accurate and vehicle-specific key fob programming instructions. If you are unsure or encounter difficulties, professional automotive locksmiths or dealerships have the diagnostic tools and expertise to program your 2004 Pontiac Grand Am key fob correctly.
