Harley-Davidson motorcycles are renowned for their iconic design and powerful performance. A key component of modern Harley ownership is the convenience of the key fob, especially models from 2007 onwards. These fobs offer seamless security and ignition, but they rely on a small battery that inevitably needs replacing. If you own a 2007 Harley and are experiencing issues with your key fob, a dead battery is the most likely culprit. This guide will walk you through everything you need to know about your 2007 Harley Key Fob Battery, from identification to replacement and even resetting your fob if necessary.
Identifying Your 2007 Harley Key Fob and Battery Type
Before you rush to replace your battery, it’s important to correctly identify your key fob and the type of battery it requires. For most 2007 Harley-Davidson models, the key fob is a compact, black device designed for easy carrying. The battery compartment is usually located on the back of the fob and can be accessed without special tools.
The standard battery for a 2007 Harley key fob is a CR2032 coin cell battery. This is a common and readily available 3V lithium battery. It’s crucial to use the correct battery type to ensure optimal performance and longevity of your key fob. Using an incorrect battery type could lead to malfunction or damage to the fob.
Step-by-Step Guide to Replacing Your 2007 Harley Key Fob Battery
Replacing the battery in your 2007 Harley key fob is a straightforward process that you can easily do yourself. Here’s a simple step-by-step guide:
- Gather Your Tools and Battery: You’ll need a new CR2032 battery and a small flathead screwdriver or a similar thin tool to open the battery compartment.
- Access the Battery Compartment: Turn your key fob over to locate the battery compartment on the back. You might see a small slot or indentation designed for opening.
- Open the Compartment: Gently insert your flathead screwdriver or tool into the slot and carefully pry open the battery compartment. Avoid using excessive force to prevent damage to the fob casing.
- Remove the Old Battery: Once the compartment is open, you’ll see the old CR2032 battery. Take note of the battery’s orientation (+ side up or down) before removing it. You can usually pry it out gently with your fingertip or the edge of your tool.
- Insert the New Battery: Install the new CR2032 battery, ensuring it’s placed in the correct orientation as the old one. The positive (+) side of the battery usually faces upwards.
- Close the Compartment: Carefully snap the battery compartment cover back into place until it clicks shut securely. Ensure it’s properly closed to protect the battery and internal components from moisture and dust.
- Test Your Fob: After replacing the battery, test your key fob by attempting to arm and disarm your Harley’s security system or start the ignition. If it works correctly, you’ve successfully replaced your 2007 Harley key fob battery.
Resetting Your 2007 Harley Key Fob (If Necessary)
In some cases, after replacing the battery, your 2007 Harley key fob might require a reset to properly communicate with your motorcycle. Here are general steps for resetting Harley key fobs. Note that specific procedures might vary slightly depending on the exact model and year of your 2007 Harley:
For Fobs with Buttons (Common on some 2007 models):
- Kill Switch and Ignition: Ensure the kill switch is set to “off”. Cycle the ignition switch from “off” to “on” and back to “off” twice, then turn it “on” again.
- Turn Signal Activation: Press and release the left turn signal twice.
- PIN Display: Press the fob button. The current PIN should be displayed on your odometer.
- PIN Adjustment (if needed): If you need to change the PIN, use the left turn signal to adjust the first digit. Press the fob button twice to move to the next digit. Repeat for all five digits.
- Complete Reset: Turn the ignition off to save the settings and complete the reset process.
For Hands-Free Fobs (Less common in 2007 but possible):
- Proximity and Ignition: Bring the fob close to your motorcycle and ensure the kill switch is “off”. Cycle the ignition switch “off” to “on” and back to “off” twice, then turn it “on” again.
- Turn Signal Sequence: Press the left turn signal twice, then the right turn signal once. The current PIN should appear on the odometer.
- PIN Adjustment (if needed): Use the left turn signal to change digits, and the right turn signal to move to the next digit.
- Finalize: Complete all five digits of the PIN and turn off the ignition.
If you encounter any difficulties resetting your 2007 Harley key fob, consult your owner’s manual for specific instructions related to your motorcycle model or contact a Harley-Davidson dealership for assistance.
Maintaining Your 2007 Harley Key Fob Battery
To ensure your 2007 Harley key fob operates reliably, consider these maintenance tips:
- Regular Battery Checks: While CR2032 batteries are long-lasting, it’s good practice to check your fob battery periodically, especially if you notice decreased range or intermittent function.
- Quality Batteries: Always use high-quality CR2032 batteries from reputable brands for optimal performance and to minimize the risk of leaks or premature failure.
- Avoid Extreme Conditions: Protect your key fob from extreme temperatures, moisture, and physical damage, which can shorten battery life and affect fob functionality.
By understanding your 2007 Harley key fob battery, knowing how to replace it, and performing basic maintenance, you can ensure your key fob remains a convenient and reliable part of your Harley-Davidson riding experience.
