Lost your key fob or need to program a new one for your 2006 Mitsubishi Outlander? You might think a trip to the dealership is inevitable, costing you time and money. However, programming a key fob for your 2006 Mitsubishi Outlander can be done in your own driveway with a simple procedure. This guide provides clear, step-by-step instructions to help you program your key fob quickly and easily, saving you a potentially hefty service fee.
Before you begin, ensure you have your new key fob and are ready to follow these instructions carefully. Programming is straightforward, but precision is key.
Tools You Will Need
- Your 2006 Mitsubishi Outlander
- The key you regularly use for your Outlander
- A new, unprogrammed key fob for your 2006 Mitsubishi Outlander
- A small jumper wire or a paper clip
Step-by-Step Programming Instructions
-
Find the Data Link Connector (DLC). The DLC is essential for initiating the programming sequence. It’s located beneath the steering wheel, slightly to the right and under the dashboard. You’ll find two connectors there, but you need the black DLC connector. Pin 1 is in the top left corner, and pin 4 is the fourth pin from the top right. If you’re unsure, the image below illustrates the DLC and pin locations.
-
Insert Your Key into the Ignition (Do Not Turn). Place your existing ignition key into the ignition cylinder, but do not turn it on. Leave the key in the “off” position throughout the initial steps.
-
Connect Pin 1 and Pin 4 of the DLC with a Jumper Wire. Using your jumper wire or a bent paper clip, carefully connect pin 1 to pin 4 of the DLC. Push the paper clip ends into the pin holes firmly enough to ensure a stable connection. You may need a flashlight to see the pins clearly. Important: Make sure all doors are closed before proceeding with this step. Programming may fail if any door is open. Working in the driver’s footwell can be tight, consider moving to the passenger seat and reaching under the steering column for better access.
-
Activate the Hazard Warning Lights. Immediately after connecting the jumper wire, press the hazard warning light button six times within 10 seconds. This means switching them on and off three times each (on, off, on, off, on, off).
-
Confirmation of Programming Mode. If steps 1-4 are completed correctly, your Mitsubishi Outlander will signal that it has entered programming mode. The vehicle will automatically lock and then unlock all doors and the liftgate once. This lock cycle is your confirmation to proceed to the next step.
-
Program the Key Fob Transmitter. After the doors cycle, take your new key fob. Press the “lock” or “unlock” button on the fob once. Then, press any button on the same fob two more times within 10 seconds of the first press. Space each press by a second or two. Upon successful programming of the key fob, the door locks will cycle again, confirming the fob is programmed.
-
Program Additional Key Fobs (Optional). If you have more key fobs to program, repeat step 6 for each additional fob. You can program up to four key fobs to your 2006 Mitsubishi Outlander. Ensure you program all fobs within one minute after completing step 5. If you exceed this time, you’ll need to restart the entire procedure from step 1.
-
Finalize the Programming. Remove the jumper wire from the DLC. Take your ignition key out of the ignition. Close all doors.
-
Test Your Key Fobs. Test each programmed key fob to ensure they lock and unlock the doors and liftgate correctly from a distance.
Troubleshooting Tips
- Procedure Not Working? Double-check that you are using the correct DLC connector and pins 1 and 4. Ensure all doors are fully closed during the process. Time each step accurately, especially the hazard light sequence and the key fob button presses.
- Still Having Issues? If you are still unable to program your key fob, it’s possible there may be an issue with the key fob itself or the vehicle’s receiver. In such cases, consulting a professional automotive locksmith or your Mitsubishi dealer may be necessary.
By following these steps, you should be able to successfully program your 2006 Mitsubishi Outlander key fob and regain full keyless entry functionality without the high costs of dealership programming. Remember to visit keyfobprog.com for more helpful guides and automotive programming tips.
